Overview
The PARSTAT 2273 is the ultimate potentiostat/galvanostat/FRA, boasting superior quality and high reliability. Its exceptional impedance capability, resolution, speed, high current, and high compliance voltage continues to be the standard against which all other systems are measured.
The 2273 is designed to be the most comprehensive potentiostat/galvanostat/FRA in your laboratory. We have incorporated customer feedback to provide not only more internal maximum current but the ability to boost up to 20A and the ability to interface all the ancillary equipment customers need today for their unique research.
Unlike any other potentiostat on the market today, the 2273 offers a unique combination of compliance voltage up to ±100V, ±10V scan ranges, and a maximum current of up to ±2A. The 2273 hardware combined with PowerSINE software can perform EIS experiments from 1MHz to 10µHz. These measurements can control either potentiostatic (Single Sine, Fast MultiSine, or Mott-Schottky), or galvanostatic, (Galvanostatic EIS) experiments.
- 2A current max. (20A boosted)
- 100V compliance
- 1.2fA current resolution
- >1013 Ωinput impedance
- <5pF of capacitance
- 10µHz to 1MHz built in analyzer
Specifications
|
Power Amplifier |
|
Compliance Voltage |
±100V |
Maximum Current |
±2A |
Rise Time |
<250ns (no load) |
Slew Time |
>15V/µs (no load)
|
System Performance |
|
Minimum Time Base |
20µs |
Minimum Potential Step |
2.5µV |
Noise and Ripple |
<50µV/rms (typical) |
Minimum Current Range |
2nA (hardware) |
Minimum Current Range |
40pA (after 50x gain) |
Minimum Current Resolution |
1.2fA
|
iR Compensation |
|
Positive Feedback Range |
2000MΩ to 2Ω (depending on current range) |
Current Interrupt |
16 bit DAC Potential Error Correction
|
Current Measurement |
|
Ranges |
12 decades, 2A to 40pA (with internal gain applied) |
Accuracy (dc) |
20µA to 2A: <0.4% Full Scale 20nA and 1µA Ranges: <0.5% 2nA<0.75%
|
Differential Electrometer |
|
Input Bias Current |
<5pA at 25°C |
Max. Voltage Range |
±10V |
Max. Input Voltage Differential |
±10V |
Bandwidth |
3dB @ >15MHz |
Common Mode Rejection |
>80dB at 100Hz >60dB at 100kHz |
Input Impedance |
>1013 Ω in parallel with <5pf
|
Impedance (EIS) Option |
|
Mode |
Potentiostat/Galvanostatic |
Frequency Ranges |
10µHz to 1MHz |
Minimum AC Voltage Amplitude |
0.1mV RMS |
Sweep |
Linear or Logarithmic
|
Interface |
|
Digital Inputs/Outputs |
5 TTL logic outputs, 2 TTL logic inputs
|
Interface |
|
Ext In |
±10V analog input.Input Impedance is 4.0kΩ |
E Monitor |
Front-panel analog output of current readings Range ±10V, 50Ω output impedance |
I Monitor |
Front-panel analog output of current readings Range ±10V, 50Ω output impedance, 0 to 2V corresponds to ±full-scale current range
|
Interface |
|
DAC Voltage Output |
±10 range BNC Connector (for stirrers, rotating disk electrode, etc.) |
Potential/Current Control |
|
Bias DAC |
16 bits resolution ±10V range (potentiostat) ±100% of full-scale current (galvanostat) |
Modulation DAC |
16 bits resolution
|
Frequency Response (small signal) |
|
2mA Range |
3dB at >1MHz, 1k source impedance |
20µA Range |
3dB at >100kHz, 100k source impedance
|
PC/Software |
|
Communication Interface |
Universal Serial Bus (USB) |
Operating System |
Windows 98/2000/NT/XP/Vista/Windows 7 |
PC Specifications (minimum) |
Pentium 3 (1GHz) / 512MB memory |
Software |
PowerSINE PowerCORR PowerCV PowerPULSE PowerSTEP
|
General |
|
Power |
600 watts max. 90/130V AC or 200/260V AC, 50-60Hz |
Dimensions |
58cm W x 47.6cm D x 22.9cm H 20” W x 18.75” D x 9” H |
Weight |
31kg (68lbs) |
Temperature |
0-50°C |
Humidity |
95% maximum relative humidity, non-condensing |
Altitude |
Up to 2,000m
|
Comments are closed.